Why 10 Windows are stupid. What to do if your computer or laptop starts to slow down or runs slowly

Many Windows 10 users note a large abundance of shortcomings in the new and still raw system. One of the most unpleasant ones is that Windows 10 slows down on some computers, which greatly complicates the work of PC owners. Below are detailed all the issues that are the main reasons that the "Tenth" OS is functioning slowly, as well as specific recommendations for eliminating the reasons why the system is working with brakes.

Causes

Obviously, this may be the result of non-compliance with the requirements of the new system from Microsoft for some parameters of the PC hardware, which is often a consequence of subsequent OS failures.

The most common reasons due to which there are problems in the functioning of Windows 10:

1. Weak processor;
2. Winchester defects;
3. Small amount of RAM;
4. Excessive number of applications on startup;
5. Viruses;
6. Other.

If the processor parameters do not meet the requirements of the new OS

This is often revealed by simple diagnostics in the form of watching a movie in high image quality. If there are jerks and so-called "brakes" during the broadcast of the video, then it is often possible to conclude that the main element of the PC is insufficient power - the processor, which does not meet the stringent requirements of the new "Ten". In order to make sure that the conclusion is correct, the following simple sequence of actions must be performed:

1. Open "Task Manager";
2. After that, go to the "Performance" tab;
3. Analyze the degree of processor load (if the percentage value is very large, then the reason for the braking is correctly identified).

It is necessary to upset users who are faced with this particular nuisance that there are only two ways out of this situation:

1. Install a new processor in the computer, replacing this old basic element from the PC components with another, but already of increased power;
2. Roll back to the previous OS version.

Inconsistency or defects in the hard drive

A damaged or insufficient volume used hard drive in a computer is often a consequence of the slow functioning of a highly demanding operating system with index 10. At the same time, the hard disk simply may not have enough time to execute all OS commands with sufficient speed. But don't rush to replace this expensive piece of PC hardware. Before you run to buy a new one, it is recommended to perform the defragmentation procedure for the current one.

Follow these steps:

Regular execution of this operation allows you to optimize the speed of interaction of the system with the extraction of information from the memory of the hard drive. But if the increase in speed did not allow obtaining tangible results and eliminating the problem, then the PC owner will have to buy a new disk.

Lack of RAM

One of the most common reasons for the observed "brakes" in Windows 10 is precisely the lack of RAM. The beautiful design and design of the windows of the new OS, as well as almost the entire list of modern applications, imply the use of a significant amount of "RAM". Unfortunately, the best way out of this situation is only to buy and equip your computer with a bracket with an increased amount of memory.

Insufficient paging file

Often, immediately after installation, the "Ten" works slowly due to a small swap file.

In order to increase its volume, the following actions are required:

Excessive number of applications on startup

To this end, several steps must be taken:

Malicious software

Any operating system is at risk of infection. The new OS is equipped with a special application "Windows Defender".

It is required with its help or with the use of a reliable anti-virus utility installed in the PC to analyze the computer memory for threats and then get rid of the detected malware.

Other

When there is a particularly noticeable slowdown in the processes of performing user tasks in a computer with Windows 10, it is recommended to perform the following several actions:

1. Open "Task Manager";
2. Then go to the "Processes" tab;
3. Find out which process takes up the most PC memory;
4. Determine the essence and degree of importance of the "gluttonous" process, and, if possible, complete it.

Rostislav Kuzmin

Greetings to everyone on my blog! Almost all laptops work great right out of the box and do not cause problems. However, after a while, the user notices that the laptop slows down and freezes. What to do if Windows 10 does not want to work correctly, I will tell you in this article and try to find all the ways to solve the problem.

From my own experience, as well as from the stories of customers who buy equipment from me, we can safely conclude that the performance of Windows 10 is broken after some time of operation, sometimes this process occurs after 1-2 months, and sometimes after a year.

Below are the reasons that can cause system performance problems.

How to clean your laptop so it doesn't slow down

By cleaning a laptop, I mean not only cleaning it from physical debris and dust, but also cleaning the operating system from unnecessary files, viruses and heavy programs. How to clean the laptop from dust so that it does not slow down below.

Cleaning a laptop from dust is a procedure that I recommend to my clients and readers to do it at least once every six months. There is no need to wait for equipment to freeze and slow down, as performance is not the biggest problem that dirt accumulation can cause. In the worst case, the device may overheat and burn.

It is very simple to understand that the problem lies in dust:

• the laptop gets very hot;
• some time after work, the laptop starts to freeze and slow down;
• the device makes a lot of noise;
• after a while, the laptop turns itself off and after a while turns on again.

What can be done if the laptop is overheating - clean and change the thermal paste. From personal experience, I can say that it is quite possible to do this on your own, but if there are some doubts about success, then it is better to turn to specialists. As a rule, it takes less time than to disassemble and assemble everything yourself, because for cleaning you will need to remove all the parts and then put them back in place. You can check the quality of cleaning and efficiency using numerous programs that can measure the temperature of the processor and video card. With their help, you can track what temperature was before and after cleaning the device.

An example of such programs can be:

Normal performance of devices:

• processor - in idle mode about 50-55 degrees, at loads up to 65;
• video card - from 50 to 70 degrees;
• hard disk - 25-40, up to 50 degrees is allowed if the device works for a long time without turning off.

What programs slow down the laptop

If the laptop starts to slow down, but it is obvious that it is not overheating, then most likely the problem is in the garbage in the form of data from remote programs and games. In addition, the problem may lie in old software, namely device drivers or a large number of startup programs. There are programs that themselves have large requirements, and if several of them are running at the same time, then at times the device may start to freeze or respond slowly to requests.

Updating drivers

To update drivers, you can use special utilities or download new versions from the manufacturer's website. If you choose the second option, then just go to the laptop manufacturer's website, find the download / driver / support tab and select your model. After that, you should select the operating system and download all the drivers for the device. They are installed like the most common programs. After installation, if the laptop itself does not ask you to restart it, this must be done forcibly for all changes to take effect.

Of course, the above method is quite effective and reliable, because there is no danger of downloading viruses instead of the driver. The disadvantage of this method is that it is quite lengthy, because it is much easier to update everything at once. To do this, special utilities are suitable that scan the laptop and find all the drivers, and then update them automatically.

List of the most popular driver software:

1. Intel Driver Update Utility Installer. A proprietary program from Intel that allows you to find drivers for all hardware from this brand. If desired, using the utility, you can find drivers for components that are not used in this device.
2. AMD Driver Autodetect is an analogue of the previous program from AMD.
3. Nvidia Update - software for updating the driver for the company's video cards.
4. DriverPack Solution - the program that is the most convenient and practical to use. In fact, this is a large database with all kinds of drivers for various devices and components. Works online and offline. In the second case, it takes about 10 GB of hard disk space.
5. Driver genius - allows you not only to manage drivers, but also to remove unnecessary or non-working ones, as well as to get complete information about the hardware in the laptop.
6. Driver Booster is a driver updater designed specifically for gamers. In one click, it finds new drivers (adapted to speed up the system in games) and removes old unnecessary software for devices. Has a free and paid version.

After updating the drivers, you should take care of cleaning the device from viruses. Of course, it is better to immediately install a licensed antivirus and prevent infection of the system, but if this was not done on time, then you can install a trial version and run the system. The best options from the company Kaspersky and ESET... I do not recommend using free software, since in fact there is no benefit from it.

Cleaning from unnecessary programs

If all of the above actions did not give a special effect, then it is time to start removing unnecessary programs. First of all, you need to understand what programs slow down your laptop. First, check the startup list. This can be done through the task manager, which is opened using the combination ctrl-alt-delete. In a special tab, we look at what is currently launched when the laptop is turned on and turn off everything unnecessary. These actions significantly speed up the launch of the OS.

The next step is cleaning drive "C" (the one on which the system is installed):

Another good way to clean your laptop of unnecessary data is to use the CCleaner utility, it allows you to remove unnecessary software, clean the registry, delete duplicate and unnecessary files, and gives you access to work with startup. CCleaner is the answer to the question "how to fix OS crashes." With this program, you can simply clean your system once a week and prevent your laptop from slowing down. Or use a program that is already configured to clean everything, and, accordingly, it is licensed. If you want, the key can be bought at a very low price in this store... Its usual price is 1200 rubles / year.

If, after all the above actions, the laptop continues to slow down, then you should remove the programs that most affect its performance or stop their work. In order to do this, you should start the task manager again and open the "performance and processes" tab. They display all programs that are currently running and consume laptop resources. The unnecessary ones should be terminated using the button clear the task.

And you can also use the utility ( paid version) AVG PC TuneUp, which will automatically clean your computer from unnecessary garbage collected over a certain time (you can choose the cleaning and optimization time). This utility is for those who do not want to waste time looking through all the programs, whose data needs or does not need to be deleted, as in the CCleaner program. I use this program because I have to run up to 8 programs at the same time and use at least 20 chrome tabs. It also scans and allocates Windows 10 resources for the programs you use, without cluttering up the OP and loading the CPU.

Conclusion

In fact, there are a lot of reasons why a laptop slows down on Windows. In addition to those described above, there may be a banal obsolescence of equipment or a mismatch between the OS and the hardware. It makes no sense to install Windows 10 on an old laptop that has less than 4 GB of RAM. Better to stay with older versions or add more RAM. It will not cost too much, but it will be able to give a second life at least for a while. In addition, if a laptop is used for a very long time with one operating system, it will not be superfluous to reinstall it, because any cleaning will not replace a clean OS.

Thank you for attention! Subscribe to updates and come back! Best regards, Rostislav Kuzmin.

Class

Have you decided to try out the latest Windows 10 OS, installed it on your computer and faced a system lag? We will tell you what could have caused this problem and how to get rid of it.

Possible reasons

Possible reasons leading to the braking of the system include:

Troubleshooting

Let's take a closer look at these problems and look at ways to solve them.

Weak processor

If windows 10 slows down after installation, then the main reason for this behavior may be a weak processor. This is the most important component that directly affects the speed of the PC. Maybe it just doesn't pull the new OS. This is especially noticeable when watching video in high definition (which can be used to test it).

In order to check the level of CPU utilization, you must:

If the load is high, then we can say that this is what causes braking. What can be done in this case? Unfortunately, not much - just replace the processor with a more powerful one, while taking into account its compatibility with other system components.

HDD problems

Similar problems occur when the hard drive fails. A large number of bad sectors over time leads to a slowdown in the PC. One of the radical ways to get rid of this problem is to buy a new hard drive, but it is not always necessary. First you need to try defragmenting it to get rid of the crashes.

This can be done using special software, as well as using the capabilities of the OS:

Video: Install Windows 10

Lack of RAM

Often, it is the RAM that is the decisive factor in whether a computer with a new OS will slow down a lot. Programs are becoming more and more demanding on the hardware, which means they require more and more RAM. The decision in this case is quite commonplace - to buy more of it. Also, before installing Windows 10, be sure to pay attention to its requirements, and whether the computer will be able to "pull" it.

The paging file is too small

Next to the previous problem is the lack of paging file. It can also lead to brakes even on a newly installed system. The solution in this case is to increase it.

You can do it like this:

1. click on "My Computer" with the right mouse button;
2. select "Properties", then "Advanced";
3. then - "Performance", "Parameters" and go to the "Virtual memory" section;
4. here we click "Change" and increase the swap file to 2 - 3GB, which should be quite enough;
5. press "OK" and exit.

Autorun load

This problem usually occurs over time, when a large number of programs and applications appear on the computer. Many of them are registered in autorun (often even without the user's knowledge) and lead to the fact that windows 10 slows down.

To fix the situation:

You can also clean autorun using the utilityCCleaner:

1. download and install the program (distributed free of charge);
2. on the left panel, select the "Service" tab and then "Autostart";
3. in the list of programs, disable unnecessary ones.

Viruses and spyware

The new OS does not guarantee that there are no malicious programs on the hard disk (if it has not been formatted). Many of them can be quite harmless, but they often lead to serious PC problems. They can also cause system failures and braking.

A good antivirus with updated virus databases will help. You can also use the utility built into this version of the OS – Windows Defender. With the appearance of such problems with Windows 10, we recommend that you conduct a full system scan to get rid of these threats.

Photo: Windows Defender - built-in antivirus

Important! After installing a new OS, the first thing to do is install an antivirus on it, because when you access the Internet without it, you put your computer at risk.

Browser problems

Are you experiencing freezes and lags while launching your browser?

In this case, pay attention to a few points:

• make sure that the version of the search engine is up-to-date, update it if necessary;
• start the task manager and in the "Processes" tab check what exactly takes system resources;
• it might be worth clearing your browser cache and history (the easiest way to do this is with CCleaner).

We've covered a few of the most common reasons why a Windows 10 PC might slow down. Solving these problems is usually not difficult, even for novice users. If you encounter other difficulties - write in the comments to the article.

After prolonged use of a Windows-based desktop computer or laptop, users may encounter a situation where the PC has become very slow and slow. There can be many reasons for a slowdown PC.

In order to understand in detail the problem of PC slowdown, we have prepared a material in which we will consider in detail the methods and techniques that increase the PC's performance. By following our recommendations, you can regain the former performance a stationary computer or laptop with Windows OS. By returning the speed of the computer, you can enjoy various multimedia entertainment, computer games and work, while forgetting about the braking and various PC glitches.

System cleaning in Windows operating systems

Windows XP, Vista, 7, 8, 10 operating systems have their own built-in system cleaners. The main disadvantage of such cleaning agents is that they only clean trash, which the system itself creates and even then, not all.

To execute complete system cleaning from garbage, where the OS and many programs will be cleaned, you need to use third-party software. One of the best cleaning programs is CCleaner... This utility is produced by Piriform LTD.

The utility is free and downloadable CCleaner on a PC from the official website www.piriform.com. The utility has been holding for several years first in the ranking from such well-known Internet publications as The guardian, PC World, CHIP Online and many others. The utility works on Windows XP, Vista, 7, 8, 10. After installation, we will launch the utility on Windows 7.

To clear the system from garbage, use the Analysis button located at the bottom of the window.

The image shows how much junk the system has found. This is the history of the explorer when the user opens folders or copies folders. It is also browser history and various garbage created by utilities.

After analysis remove garbagefound by the utility by clicking the Cleanup button.

In such a simple way, you can increase the speed of the system and its programs. This utility does not end there. The program can also delete unnecessary registry branchesthat were created by various software. To take advantage of this opportunity, we need to open the " Registry»And, by analogy with the previous example, press the Search for problems button.

After the search, click the Fix button and thereby delete unnecessary registry entries.

The utility's functionality is not limited to this, but its coverage does not fit into the topic of the article, so we will go further. Having finished cleaning the system and registry, it's time to start defragmentationwhich we will discuss in the following examples.

Defragmentation in Windows operating systems

The operating systems Windows XP, Vista, as well as newer Windows 7, 8, 10 have their own built-in tools that allow you to do defragmentation. The only drawback of the built-in defragmenter in Windows XP, Vista, 7, 8, 10 is its work speed and weak functionality.

Therefore, it is better to use a third-party defragmenter. The best defragmenter today is a free utility Defraggler... Utility Defraggler developed by the same company as CCleaner Piriform LTD. Download Defraggler the PC folder can also be found from its official website www.piriform.com, just like CCleaner.

Installing Defraggler is quite simple and comes down to a couple of clicks, so any PC user can handle it. Besides DefragglerThere are still many quality defragmenters out there, but we chose this one as it will help us solve another problem that can cause your PC to slow down and run slowly.

Defraggler works with all current Windows operating systems from XP to Windows 10. So feel free to install and run it on any Windows. In our case, we ran Defraggler on Windows 7.

To start defragmentation, click the Defragment button at the bottom of the window. There is a button next to this button that can start an analysis of the disk for the need for defragmentation. After the start of defragmentation, you can observe it on the disk map.

This process can take a long time and depends on the size of the disk and the degree of disk fragmentation.

Utility Defraggler knows how to defragment both the entire disk and a separate folder and files. Its functionality does not end there. Also, the utility can:

• Do a quick defragmentation;
• Do the work of the program on a schedule;
• Defragment free disk space;
• Turn off the PC after defragmentation;
• Defragment the registry.

Of all the functions described, the latter is the most significant. Using defragment the registry, you can also increase the speed of your desktop computer or laptop. To use this function go to the menu " Settings"And activate defragmenting the registry when starting the PCas shown in the image.

By enabling this option, in your PC at system startup Defraggler will defragment the registry:

Now let's talk about the features of the program that we mentioned earlier. Defraggler can watch the state of your hard drive, namely S.M.A.R.T ..

S.M.A.R.T. is a built-in routine that can determine the health of a hard drive. Let's go to the " condition».

The image above shows the parameters of a good hard drive. The following image shows a hard drive with broken sectors:

If you have just such a situation, then the culprit in braking the system is winchester... Based on this, the hard drive should be replaced with a new one... In addition, in this state, the hard drive will not last long, and you can unexpectedly lose a lot of important information. Probably all.

From the example you can see that using Defraggler you can do:

• Long or fast disk defragmentation;
• Defragmenting the registry;
• Check the condition of the hard drive.

It should also be noted that if you have an SDD disk type installed in your PC, then do not defragment it, as this can shorten its lifespan.

Resolving RAM problems

Very often, the culprit for slowing down and freezing the PC is rAM... Operating systems from Windows 7 to Windows 10 have built-in memory checkers. For example, let's run the tool for checking the RAM for errors in Windows 10. To do this, use the search in the top ten and enter the phrase “ Memory Checker».

Now let's run the found utility.

In the window that opens, select the first item, after which the computer will restart and rAM diagnostics will start.

After a long check, the computer will boot and the user will be presented with the check result. If the result of the check is negative, this means that the RAM must be replaced with a new one.

Older operating systems such as Windows XP do not have a built-in memory check. It follows from this that on Windows XP, to check the memory, you should use third-party software... One of the most popular utilities can do a RAM check Memtest86.

Speed \u200b\u200bup with ReadyBoost

Sometimes even all the actions taken to eliminate braking and glitches in the PC do not help properly. This is due to the fact that on your PC weak hardware... To solve this problem in the OS, starting with Windows 7 and ending with Windows 10, the user has the opportunity to use the technology ReadyBoost.

The essence of the technology ReadyBoost is to use fast USB drives for caching data. That is, using ReadyBoost, you can replace the standard swap file on a screw, onto a fast USB stick.

For example, we will use a Windows 10 PC and a USB flash drive with an interface USB 3.0... You ask why exactly USB 3.0. The answer is simple, this interface very fast and is most suitable for our task. Insert the flash drive into the PC and go to it properties to the " ReadyBoost».

Now let's select an item in the window to speed up our system as shown in the image above and click the Apply button. The configuration is done in the same way in Windows 7 and 8.

After these actions, the system should noticeably accelerate, the long start of programs and braking should disappear.

If you want to use the described technology on Windows XPthen use a third-party program eBoostr.

Other ways to speed up a desktop computer or laptop and remove the brakes

If the above examples did not help, then the following methods will help to solve the problem with brakes and glitches:

• Change of antivirus program;
• Disable visual effects;
• Stop unnecessary services;
• Reinstalling the operating system;
• Upgrading seven to ten.

If you have a good antivirus program installed on your stationary computer or laptop, then on a modern PC you are reliably protected and this does not affect the system performance. But if you have a weak laptop or stationary computer, it will be noticeable how the antivirus began to slow down the system.

To remedy this situation, Panda Security SL has developed an antivirus Panda Cloud Antivirus, which practically does not waste the system resources of a weak PC. The secret of this antivirus is that all complex operations are performed in the cloud.

In addition to antivirus, the performance of a weak laptop or stationary computer can be affected oS visual effects... Starting with Vista, Windows uses various visual effects that slow down the PC. To turn off visual effects, for example, in Windows 10, you need to go to system properties. For this in the program Execute let's type the command "sysdm.cpl".

Going to the system properties, open the tab " Additionally". In the text block of performance, click on the Options button.

A window should open in front of us where you can disable and enable visual effects in Windows 10.

Visual effects are configured in the same way in Windows 7 and 8. If we talk about Windows XP, then it makes no sense to disable its visual effects, since they already consume few resources.

You need to be careful with disabling services, as this can lead to incorrect operation of the operating system. To stop unnecessary services, for example, in Windows 7, you need to go to the snap-in responsible for services. For this in the program Execute we will type the command "services.msc". After execution, the snap-in " Services».

Any service can be disabled in this snap-in. Before disabling an unnecessary service, make sure that disabling this service is absolutely safe for the system. For example, you can stop the service " Print manager”If your PC is not using a printer.

Another way is complete system reinstallation... After reinstalling Windows, you will immediately notice how fast your laptop or all-in-one is working. This happens because the OS is new and has a clean registry and no garbage. In many cases, reinstalling the OS will help revitalize your laptop or desktop PC and get rid of the brakes.

In addition to reinstalling, there are times when the user of the seven upgrades the system to Windows 7 and it works slowly after that. Slow system performance is associated with the way updates are distributed and with hardware. In the first case, the slow operation is associated with a new type of update delivery in the P2P network. That is, updates travel from user to user. In the second case, the slow work is associated with the old iron. In this case, only updating components or buying a new laptop will help.

Summing up

We hope all the material presented in the article will help our readers and you will not have any questions why the PC began to slow down or why the laptop or candy bar began to freeze. I would also like to give a couple of tips to our readers.

If the brakes and freezes in the system do not pass, then malware may be the culprit of your problem. In this case, you should perform a full scan of the system for viruses and remove them from the found folder.

In addition, if you own a PC with Windows XP, then it's time for you to think about changing the OS to a more secure one. XP support has ended long ago and new antiviruses do not support it for a long time. This means that the system is very insecure and if you give such a system access to the Internet, then you can face real problems due to viruses. Due to viruses, you can face both system brakes and theft and damage of personal information.

Related Videos

Why is Windows 10 slow? Progress does not stand still, this also applies to Windows operating systems. Yesterday the flagship of Microsoft was Windows 7, today Windows 10 already exists. There are many reasons, it is worth considering the most common of them.

Why does it slow down?

Possible causes of inhibition include a dozen problems, including:

• insufficient power of the central processor;
• unstable work of the hard disk (hard drive);
• insufficient amount of random access memory (RAM);
• insufficient paging files;
• overloaded automatic start;
• the presence of viruses and spyware;
• difficulties in the work of browsers.

Ways to solve problems

There are several solutions to the problem:

1. Insufficient CPU power. If Windows 10 slows down, then the determining cause may be an insufficiently powerful processor or its "fatigue". It means that it simply cannot provide normal operation of the operating system. You can easily identify this problem by turning on any video with the maximum resolution. Next, you need to determine how loaded the central processor is. To do this, go to the task manager and select the "Performance" tab, estimate the percentage of workload. If the figure is large, then the reason lies precisely here, and therefore the computer slows down. Solution: it must be replaced with a new and more powerful model. In this case, it is necessary to assess its compatibility with all components.
2. Unstable operation of the hard disk (hard drive). A factor can arise when it malfunctions. Bad clusters or sectors result in slow data transfer through the system. The fix for this problem can be the purchase of a new hard drive, but do not rush. First you need to check for errors. Basic can help with this. You go to the main menu, enter "Disk defragmentation" into the search bar and launch it. Next, the disk to be scanned is selected and the analysis is started. You must wait until it ends. The duration of the analysis depends on the size of the hard drive and can reach several hours. During the test, it is unacceptable to turn it off or interrupt the operation of the PC.
3. Insufficient random access memory (RAM). As a rule, this is the main reason for system braking. Over time, every digital product becomes very demanding on the configuration of a computer or laptop and, as a result, more RAM is required. Solution: Upgrade your PC with more memory.
4. Insufficient paging files. The factor directly depends on the previous one. It can also cause the OS to run slowly. The solution is to increase the swap space. It is carried out as follows - right-clicking on the shortcut "My Computer", select "Properties", then "Advanced", "Performance", "Options" and go to the "Virtual memory" tab. You need to change this parameter to 2 or 3 gigabytes. This should be enough to stabilize the system. And, as a result, the "Ok" button.
5. Automatic startup overloaded, while the laptop slows down? This problem appears with the installation of many programs that are registered in the autorun, which can lead to the fact that Windows starts to slow down. The solution is as follows: the "Start" button, "MSCONFIG" is written in the line and you go to the "Autorun" attachment. Next, you need to turn off all programs that you consider unnecessary in your work. Autostart cleaning is performed using additional software that can be downloaded for free on the Internet.
6. The presence of viruses and spyware. Viruses contribute to all sorts of problems with the computer. In the event that Windows 10 was installed without formatting the hard drive, it is likely that viruses could remain and continue their activities to destabilize work. Solution: Purchase a good antivirus utility. It is recommended to install it immediately after installing the operating system.
7. Difficulties in the work of browsers. If your browser becomes slow, you need to make sure you are using the latest version of the search engine. Also, it will not be superfluous to consult the Task Manager to determine which process is taking over too many resources. If necessary, clear the history and cache. You can do this in your browser or use additional free programs.

Why does the computer slow down? Don't forget that browser instability is closely related to hacker attacks. Quite often, with the help of additional programs, they can take over your data in order to make a profit. It is because of this that slowness arises in work. Antivirus can deal with this problem, even the one that is installed with Windows 10.

This could be due to outdated or incompatible network adapter drivers. If the Windows 10 update happened recently, then it is likely that the existing driver is capable of working only with the old version. To do this, it is recommended to check for the latest driver version.