IP212-52M - single-position linear detectors, consisting of a transceiver and a reflector reflector. In the transceiver, the optical channels are separated and isolated in a two-chamber optical system.
As a reflector-reflector IP212-52M uses a high-performance reflector (reflector), capable of performing its functions even when its surface deviates relative to the optical beam by ±10 - 15 degrees.
Operating principle:
The principle of operation of the detectors is based on the property of reducing the power of an optical beam that has passed through a smoky environment. The detector's transmitter generates periodic bursts of infrared pulses.
A significant difference in the operation of two-position and single-position detectors is that in the first case the optical beam overcomes the controlled space once, and in the second case it needs to do this twice. As a result, the attenuation of the received signal for the same smoke level for the second case will be much greater, which makes it possible to set guaranteed-distinguishable response thresholds with a shorter interval. Depending on the size of the protected premises or other features of the application, IP212-52M can be set to four response thresholds (50%, 40%, 30% and 20%).
The consumption of detectors is minimized through the use of original solutions for synchronizing the operation of the receiver and transmitter (for IP212-52M - no more than 1.5 mA), which allows them to be used with control panels in a two-wire connection. The IP212-52M detectors make it possible to connect almost any fire and security devices with both alternating and unipolar voltage to the loops.
In IP212-52M, only the forced synchronization mode is always used (by default, as it is many times more noise-resistant).
On the rear side of the transceiver housing there are terminal blocks for external connections, as well as a program switch for the detector operation tactics.
The IP212-52M detectors include remote devices UV-PRD-PRM, the appearance of which is shown in the figure.
Specifications:
Parameter | Meaning |
Set thresholds: for IP212-52M | 20%, 30%, 40%, 50% |
Range of controlled distances | from 8 to 100 m |
Maximum width of space protected by one detector | no more than 9 m |
Room area protected by one detector | no more than 900 m2 |
Supply voltage for detectors (receiver, transmitter and transceiver) | 10 to 30 V |
Current consumed by the detectors in the "Normal" mode: IP212-52M | no more than 1.5 mA |
Current consumed by the transmitter when powered from a separate source (in any mode of operation) | no more than 1 mA |
The current consumed by the receiver in the modes: | no more than 11 mA |
The magnitude of the current jump during the formation of the signal "Attention" | |
Leakage current when powered by reverse polarity voltage | no more than 2 uA |
Power off duration for reset | at least 2 s |
The response time of the detector: | 5 s |
The inertia of fixing the notice "Fault" in the modes: | 3 to 5 s |
The value of the resistance of the closed contacts of the opto-relay: | 15 ohm |
The value of the resistance of the open contacts of the opto-relay | not less than 500 kOhm |
The value of the insulation resistance of the output opto-relay circuits from the power supply circuits of the detector | not less than 500 kOhm |
Current switched by opto-relay outputs | no more than 100 mA |
Voltage switched by opto-relay outputs | no more than 100 V |
Sensitivity Compensation Limit | |
Compensation rate: | 0.12%/min |
Overall dimensions of the transceiver: | no more than 140x135x70 mm |
Transceiver weight: | no more than 0.4 kg |
Overall dimensions of remote devices UV-PRD-PRM | no more than 55x55x21 mm |
Weight UV-PRD-PRM | no more than 0.04 kg |
Overall dimensions of reflector-reflector IP212-52M | no more than 246x210x13 mm |
Mass of reflector-reflector IP212-52M | no more than 0.25 kg |
Operating temperature range | from minus 30 to + 55°C |
Maximum Permissible Relative Humidity | |
Maximum allowable vibration frequency | |
Maximum allowable illumination at the installation site | |
The degree of rigidity in terms of resistance to EMF | fourth |
The degree of protection of the shell in accordance with GOST 14254 |
Advantages of buying in TD Aktiv-SB:
Information about the technical characteristics, scope of delivery and appearance of the goods is for reference only and is based on the latest information available at the time of publication.
Designed to detect fires accompanied by the appearance of smoke, and transmit the signal of the alarm message "Fire" or "Attention" to control panels; for use in rooms with a large area, large length or high ceilings.
Peculiarities
The detector can be connected to the control panel using either a two-wire or a four-wire alarm loop.
Additional Information
The detector is designed for continuous round-the-clock operation and is used in enclosed spaces of residential and industrial buildings and structures in conjunction with fire control panels (for example, PPK-2, PPK-2M, Raduga, Signal-20P, etc.) and with security and fire control panels (for example, "Akkord", "Nota", "Signal-20", "Signal-VK", "VERS", "Granit", "Vista", etc.).
The principle of operation of the detector is based on the property of reducing the intensity of an optical beam that has passed through a smoky environment. IP212-52M operates in the infrared wavelength range. During installation, the transceiver and reflector-reflector are located opposite each other and adjusted in order to achieve maximum coincidence of the transceiver's radiation pattern with the direction to the reflector. When operating in the normal mode, the transceiver periodically (with an interval of 350 ms) generates bursts of infrared pulses (IR pulses), which, having passed through the controlled environment, reflected from the reflector and again overcome the controlled distance, return to the transceiver, are received and processed by him.
The decision about the presence of smoke in the protected space is made when the intensity of the optical beam decreases to a threshold value (relative to the intensity of the optical beam in a smoke-free environment). The trigger threshold can be selected by setting the operation tactics to 20%, 30%, 40% or 50%. Due to the fact that the beam crosses the controlled space twice, the decrease in beam intensity in percentage terms will be greater than the threshold value and will be: 36% for the 20% threshold, 49% for the 30% threshold, 64% for the 40% threshold and 75% for the 50% threshold. If the beam intensity decreases by more than 98% (corresponds to the threshold of 86%), the notification "Fault-beam" will be recorded.
Linear smoke detector 8-80m
IP212-52M - single-position linear detectors, consisting of a transceiver and a reflector reflector. The appearance of the transceiver is shown in Figure 1. In the transceiver, the optical channels are separated and isolated in a two-chamber optical system.
As a reflector-reflector IP212-52M uses a high-performance reflector (reflector), capable of performing its functions even when its surface deviates relative to the optical beam by ±10 - 15 degrees. The appearance of the reflector-reflector is shown in Figure 2.
On the rear side of the transceiver housing there are terminal blocks for external connections, as well as a program switch for the detector operation tactics (see Figure 3).
The IP212-52M detectors include remote devices UV-PRD-PRM, the appearance of which is shown in Figure 4.
IP212-52M detectors include remote devices UV-PRD-PRM. The design and appearance of remote devices is shown in the figure.
Operating principle
The principle of operation of the detectors is based on the property of reducing the power of an optical beam that has passed through a smoky environment. The detector's transmitter generates periodic bursts of infrared pulses.
A significant difference in the operation of two-position and single-position detectors is that in the first case the optical beam overcomes the controlled space once, and in the second case it needs to do this twice. As a result, the attenuation of the received signal for the same smoke level for the second case will be much greater, which makes it possible to set guaranteed-distinguishable response thresholds with a shorter interval. Depending on the size of the protected premises or other features of the application, IP212-52M can be set to four response thresholds (50%, 40%, 30% and 20%).
The consumption of detectors is minimized due to the use of original solutions for synchronizing the operation of the receiver and transmitter (for IP212-52M - no more than 1.5 mA), which allows them to be used with control panels in a two-wire connection. The IP212-52M detectors make it possible to connect almost any fire and security devices with both alternating and unipolar voltage to the loops.
In IP212-52M, only the forced synchronization mode is always used (by default, as it is many times more noise-resistant).
Technical specifications
| Parameter | Meaning |
| Set thresholds: for IP212-52M | 20%, 30%, 40%, 50% |
| Range of controlled distances | from 8 to 100 m |
| Maximum width of space protected by one detector | no more than 9 m |
| Room area protected by one detector | no more than 900 m2 |
| Supply voltage for detectors (receiver, transmitter and transceiver) | 10 to 30 V |
| Current consumed by the detectors in the "Normal" mode: IP212-52M | no more than 1.5 mA |
| Current consumed by the transmitter when powered from a separate source (in any mode of operation) | no more than 1 mA |
| The current consumed by the receiver in the modes: - formation of the output signal "Attention" - formation of the output signal "Fire" - formation of the output signal "Fault" in the "Relay" mode - formation of the output signal "Fault" in the "Key" mode | no more than 11 mA no more than 35 mA no more than 11 mA no more than 1.5 mA |
| The magnitude of the current jump during the formation of the signal "Attention" | 7.5±0.75mA |
| Leakage current when powered by reverse polarity voltage | no more than 2 uA |
| Power off duration for reset | at least 2 s |
| The response time of the detector: typical maximum | 5 s 10 s |
| The inertia of fixing the notice "Fault" in the modes: "Fault - memory", "Fault - tolerance" "Fault Is a Beam" "Fault - synchronization", "Fault - failure" "Fault - excess", "Fault - decrease" | 3 to 5 s 2±0.5 s from 40 to 70 s from 40 to 70 s |
| The value of the resistance of the closed contacts of the opto-relay: typical maximum | 15 ohm 25 ohm |
| The value of the resistance of the open contacts of the opto-relay | not less than 500 kOhm |
| The value of the insulation resistance of the output opto-relay circuits from the power supply circuits of the detector | not less than 500 kOhm |
| Current switched by opto-relay outputs | no more than 100 mA |
| Voltage switched by opto-relay outputs | no more than 100 V |
| Sensitivity Compensation Limit | 3 dB (50%) |
| Compensation rate: in quick compensation mode in slow compensation mode | 0.12%/min 0.03%/min |
| Overall dimensions of the transceiver: without adjusting device with adjustment device | no more than 140x135x70 mm no more than 185x150x140 mm |
| Transceiver weight: without adjusting device with adjustment device | no more than 0.4 kg no more than 0.6 kg |
| Overall dimensions of remote devices UV-PRD-PRM | no more than 55x55x21 mm |
| Weight UV-PRD-PRM | no more than 0.04 kg |
| Overall dimensions of reflector-reflector IP212-52M | no more than 246x210x13 mm |
| Mass of reflector-reflector IP212-52M | no more than 0.25 kg |
| Operating temperature range | from minus 30 to + 55°C |
| Maximum Permissible Relative Humidity | 98% |
| Maximum allowable vibration frequency | 55 Hz |
| Maximum allowable illumination at the installation site | 12,000 lux |
| The degree of rigidity in terms of resistance to EMF | fourth |
| The degree of protection of the shell in accordance with GOST 14254 | IP40 |
Adjustment
The adjustment process is similar to the process described for IP212-52. The choice of tactics for the detectors IP212-52M is similar to IP212-52 but has its own differences. General and individual settings of the detectors operation tactics are given in the table.
| engine number switch | Detector operation mode | |
| Disabled (OFF) | Enabled (ON) | |
| General settings | ||
| 1 | Regular mode of operation | Adjustment mode |
| 2 | Output signal generation mode "Fire" | Output signal generation mode "Attention" |
| 4 | Quick Sensitivity Compensation Mode | Slow Sensitivity Compensation Mode |
| Installations for IP212-52 | ||
| 3 | Self-synchronization mode (by beam) | Forced synchronization mode (via communication line) |
| 5 | Threshold 50% ("6"-OFF) | Threshold 37% ("6" - OFF) |
| 6 | Threshold 50% ("5" - OFF) | Threshold 25% ("5" - OFF or ON) |
| Installations for IP212-52M | ||
| 3 | Output "Fault-relay" | Output "Fault-Key" |
| 5 | Threshold 50% ("6"-OFF) 30% ("6"-ON) | Threshold 40% ("6"-OFF) 20% ("6"-ON) |
| 6 | Threshold 50% ("5"-OFF) 40% ("5"-ON) | Threshold 30% ("5"-OFF) 20% ("5"-ON) |
To facilitate the adjustment process, it is recommended to use service equipment tester IPDL-52.
Delivery set of the detector IP212-52M with a range of 8 to 80 m
Note. The ceiling bracket is not included in the main set and is supplied by separate order.
FIRE ALARMS \ Fire detectors
Linear optical smoke detector, single-position, range from 8...80 m, 2 switching schemes: powered by an alarm loop and from a separate power source, 3 output relays (FIRE-NC, FIRE-NO, FAULT-NC), U-supply 10...30V, I-cons. 1.5 mA, IP40, t-work.-30...+55°C, 185x150x140 mm (with adjustment device).
IP212-52M - single-position linear detectors, consisting of a transceiver and a reflector reflector. The appearance of the transceiver is shown in Figure 1. In the transceiver, the optical channels are separated and isolated in a two-chamber optical system.
As a reflector-reflector IP212-52M uses a high-performance reflector (reflector), capable of performing its functions even when its surface deviates relative to the optical beam by ±10 - 15 degrees. The appearance of the reflector-reflector is shown in Figure 2.
On the rear side of the transceiver housing there are terminal blocks for external connections, as well as a program switch for the detector operation tactics (see Figure 3).
The IP212-52M detectors include remote devices UV-PRD-PRM, the appearance of which is shown in Figure 4.
IP212-52M detectors include remote devices UV-PRD-PRM. The design and appearance of remote devices is shown in the figure.
Operating principle
The principle of operation of the detectors is based on the property of reducing the power of an optical beam that has passed through a smoky environment. The detector's transmitter generates periodic bursts of infrared pulses.
A significant difference in the operation of two-position and single-position detectors is that in the first case the optical beam overcomes the controlled space once, and in the second case it needs to do this twice. As a result, the attenuation of the received signal for the same smoke level for the second case will be much greater, which makes it possible to set guaranteed-distinguishable response thresholds with a shorter interval. Depending on the size of the protected premises or other features of the application, IP212-52M can be set to four response thresholds (50%, 40%, 30% and 20%).
The consumption of detectors is minimized through the use of original solutions for synchronizing the operation of the receiver and transmitter (for IP212-52M - no more than 1.5 mA), which allows them to be used with control panels in a two-wire connection. The IP212-52M detectors make it possible to connect almost any fire and security devices with both alternating and unipolar voltage to the loops.
In IP212-52M, only the forced synchronization mode is always used (by default, as it is many times more noise-resistant).
Technical specificationsParameter | Meaning |
Set thresholds: for IP212-52M | 20%, 30%, 40%, 50% |
Range of controlled distances | from 8 to 100 m |
Maximum width of space protected by one detector | no more than 9 m |
Room area protected by one detector | no more than 900 m2 |
Supply voltage for detectors (receiver, transmitter and transceiver) | 10 to 30 V |
Current consumed by the detectors in the "Normal" mode: IP212-52M | no more than 1.5 mA |
Current consumed by the transmitter when powered from a separate source (in any mode of operation) | no more than 1 mA |
The current consumed by the receiver in the modes: | no more than 11 mA |
The magnitude of the current jump during the formation of the signal "Attention" | |
Leakage current when powered by reverse polarity voltage | no more than 2 uA |
Power off duration for reset | at least 2 s |
The response time of the detector: | 5 s |
The inertia of fixing the notice "Fault" in the modes: | 3 to 5 s |
The value of the resistance of the closed contacts of the opto-relay: | 15 ohm |
The value of the resistance of the open contacts of the opto-relay | not less than 500 kOhm |
The value of the insulation resistance of the output opto-relay circuits from the power supply circuits of the detector | not less than 500 kOhm |
Current switched by opto-relay outputs | no more than 100 mA |
Voltage switched by opto-relay outputs | no more than 100 V |
Sensitivity Compensation Limit | |
Compensation rate: | 0.12%/min |
Overall dimensions of the transceiver: | no more than 140x135x70 mm |
Transceiver weight: | no more than 0.4 kg |
Overall dimensions of remote devices UV-PRD-PRM | no more than 55x55x21 mm |
Weight UV-PRD-PRM | no more than 0.04 kg |
Overall dimensions of reflector-reflector IP212-52M | no more than 246x210x13 mm |
Mass of reflector-reflector IP212-52M | no more than 0.25 kg |
Operating temperature range | from minus 30 to + 55°C |
Maximum Permissible Relative Humidity | |
Maximum allowable vibration frequency | |
Maximum allowable illumination at the installation site | |
The degree of rigidity in terms of resistance to EMF | fourth |
The degree of protection of the shell in accordance with GOST 14254 |
Adjustment
The adjustment process is similar to the process described for IP212-52. The choice of tactics for the detectors IP212-52M is similar to IP212-52 but has its own differences. General and individual settings of the detectors operation tactics are given in the table.
engine number | Detector operation mode |
|
General settings |
||
Installations for IP212-52 |
||
Installations for IP212-52M |
||
Delivery set of the detector IP212-52M with a range of 8 to 80 m
| Name | Quantity |
| Linear fire detector IP212-52M (IPDL-52M) consisting of: | |
| Transceiver | 1 |
| Reflector-reflector | 1 |
| Accessory set: | |
UV-PRD-PRM Wall bracket | |
| Ceiling bracket | 1 (see note) |
| Holder | 1 |
| Bolt 5X16 GOST 7805-70 | 4 |
| Bolt 5X35 GOST 7805-70 | 2 |
| Washer 5.10.016 GOST10450-78 | 6 |
| Mounting kit1 | |
| Screw 4X30 DIN 7996 | 8 |
| Dowel 6X30 | 8 |
| Mounting kit1 | |
| Screw 3×20 | 4 |
| Dowel S 5×25 | 4 |
| Manual | 1 |
Note. The ceiling bracket is not included in the main set and is supplied by separate order.
Advantages of buying in TD Aktiv-SB:
Information about the technical characteristics, scope of delivery and appearance of the goods is for reference only and is based on the latest information available at the time of publication.
