One of the newfangled interior design trends is stripes on the walls. It would seem that there is nothing more elementary and simpler than a line drawn directly. In fact, painting striped walls is not an easy task. You can make sure of this if you carefully study the instructions before painting the striped walls.
If you intend to see the walls striped, then it is important to pay attention to the fact that the different arrangement of the stripes on the wall will be perceived completely differently. So, vertical stripes will visually increase the height of the wall surface between the ceiling and the floor, while horizontal stripes will give a feeling of freedom and spaciousness. In other words, painting striped walls suggests a choice:
- the direction in which it is preferable to see the stripes on the walls in the room;
- places where stripes will be placed (on the entire surface or on one wall);
- the effect of the action - a visually high or spacious room.
Paint striped walls: preparation for basic work
The first step is to analyze the available surface on which you plan to place the lines. The surface texture can also be painted (water-based paint, enamel, etc.), paper (covered with wallpaper) or something else.
Whatever the surface, it should first be prepared: clean it of dirt (dust, cobwebs), remove old wallpaper, if necessary, restore plaster defects, remove peeling paint. Then a primer is applied and allowed to dry.
Back to the table of contents
Choosing a stripe design
The number of straight lines, their width and colors depend entirely on personal preferences, creative imagination and, to a large extent, on the possibilities.
There are a lot of options for how the striped composition will be located, ranging from one strip around the entire perimeter and ending with wide stripes from floor to ceiling (from corner to corner). Single lines are a common technique and are often used to separate a panel area.
The pattern formed by different shades of one color segment is distinguished by originality. It is better if the shades will gradually and consistently replace one another, starting from light to dark, and vice versa. Darkening the bottom creates the illusion of a bowl; darkening the top creates a pyramidal effect.
They choose the color of the stripes, relying more on their own taste and interior parameters. There are some undesirable points to consider that you can get out of the blue by experimenting with color. For example, if the lighting in a room is dim, the cool blue tone will give the impression of an unattractive “gray” setting.
Warm tones - peach, apricot, caramel. Turquoise and sea waves are their companion flowers. The combination of burgundy, beige and pink looks beautiful.
It is not always appropriate to use many narrow stripes. Especially if each of them has its own shade. For visual perception, a sensation of obvious color oversaturation will be created. In such a colorful space, hardly anyone will have a feeling of comfortable stay in it.
It is necessary to decide in advance at what interval the alternation of lines will occur, and also to establish the sequence of the composition by color.
Back to the table of contents
We paint the striped walls ourselves
Hand-painted painting of walls in a line is within the power of most people, but not every home craftsman is aware of the intricacies of painting surfaces with a striped pattern. To facilitate the task, we will describe the entire sequence of actions in as much detail as possible.
For work you need to prepare:
- tape measure;
- chopping cord (or a string of light colors);
- crayon for pigmenting the twine;
- simple pencil;
- many buttons;
- builder level;
- shallow plastic bath;
- short-haired roller;
- masking tape;
- fly brush;
- rags.
Line painting is best done with a partner. Since this will affect the quality of the work performed, and even so it is necessary for safety reasons.
It is also quite possible for one to master everything, but the procedure will be carried out without a hydro level.
Instructions for work:
- Taking a tape measure, measure the desired width for the strip.
- From one corner of the wall to another, stretch and fasten a chopping cord or a string painted with crayon with buttons. With the assistance of the level, the plane is verified. If everything matches, pull back the center of the cord by a couple of centimeters and release. The line marked on the wall in a similar way will protrude one of the boundaries of the future strip. These steps are repeated the required number of times.
- Masking tape is applied along the resulting border markings. This technique allows you to create a clear and uniform demarcation, and when staining, eliminates the formation of smudges.
- When staining, the main actions are performed with a roller, corrective actions with a brush.
- After waiting for the paint to dry completely, the masking tape is torn off the wall surface.
If there is only one bathtub, what do they do in this case? Of course, before filling it with paint, polyethylene or foil material is laid inside. After working out one color, the film is taken out of the tray and thrown away. In place of the old one, a new one is laid under a different paint color.
After learning the intricacies of being striped, you can safely get to work.
Happy renovation!
Tired of plain walls? Want to learn how to paint stripes or even checkered walls using just a roller and masking tape? Read our new article!
Choose a high quality tape that will prevent paint from flowing underneath and that can be removed without damaging the underlying paint. For best results, apply paint on light coats, but make sure the paint is not too runny.
For stripes, use wide masking tape to divide the surface into parallel rows for neat staining. For a checkered pattern, glue the tape and paint the parallel rows in one color, first in one direction and then in the other.
TOOLS AND MATERIALS
- Level
- Pencil
- Roulette
- Small roller for applying paint
- Brush or paint roller used to apply the first coat of paint
- Latex or art acrylic paint
- Masking tape
- Sponge Applicator
Striped walls
Apply the first coat of paint in the desired color. Let the paint dry completely.
With a pencil using a level, mark the first strip with light vertical lines. Apply masking tape between the lines and press down firmly on the edges to ensure a good grip.
Measure from the first stripe and draw parallel lines for the remaining stripes in the first color. Use a level to draw vertical lines. Apply masking tape.
Color stripes brush, small roller or sponge applicator 'Let the paint dry.
Remove the masking tape from the painted strips. Repeat the process for additional colors.
Apply the first coat of a low to medium gloss latex enamel of the desired color. Let the paint dry. Measure and mark the vertical and horizontal lines for the rows of the first color. Draw light lines along the level or level with a ruler. Use plaid or plaid fabric as a reference to determine the size and position of the rows.
Attach and firmly press the masking tape between the horizontal lines to provide a good grip on the edges of the tape.
Dilute the first color with water, acrylic filler or latex conditioner. The paint should be slightly translucent when applied. Use the sponge applicator to paint over the horizontal stripes. Move the applicator from one end of the strip to the other, applying paint in thin lines that simulate a fabric pattern. Let the paint dry and then remove the tape.
Apply masking tape to make vertical stripes. With the same color and the same as for the horizontal stripes, paint over the vertical stripes. Let the paint dry and then remove the tape.
Draw horizontal and vertical stripes with lines, which will be painted in a different color. Repeat steps 2-4.
Repeat this step to color the horizontal and vertical stripes of all other colors.
TOOLS AND MATERIALS
- Paint brush or roller
- Roulette
- Level or level with ruler
- Pencil
- Sponge Applicator
- Low to medium gloss latex enamel used for the first coat
- Plaid or plaid fabric
- Masking tape
- Latex or artistic acrylic paints used to paint stripes
Repair in an apartment or house is a responsible process. Much attention is paid to the decoration of the walls. Most people today prefer to paint their walls. This is not surprising as the paint is not time consuming to apply. The coating is durable.
The greatest popularity is now beginning to acquire striped wall painting. Many do not know how to paint striped walls with their own hands correctly. Unlike the usual standard strip application, it requires some care and adherence to the most important rules, without which the result will not be of high quality.
Preparing the walls
Before you start painting the walls, you must carefully prepare the surfaces. Typically, paintable walls should be perfectly flat. This is especially true for the walls on which strips are supposed to be made. Curved walls will visually bend the stripes, which in the end will look inorganic.
So, first, the walls are completely freed from the old coating. If it is wallpaper, then it should be torn off along with the paper, if any, underneath. If there was paint under the wallpaper, it is necessary to use a special solution that provokes the swelling of the old paint and makes it possible to remove it completely and easily.
After that, you must try to remove the loose old plaster and putty. If this is not done, they will eventually fall away and break the wall. If the material is held securely, you do not need to touch it. Further, the walls are covered with a primer, sealed and putty, and, if necessary, leveled. Finally, generously apply another coat of primer and wait until it is completely absorbed.
Back to the table of contents
Design selection
The next stage is the choice of a specific design of stripes and their marking on the walls. First, decide on the width. Large striped walls can make the space smaller. Many narrow stripes will make the room colorful, which is not always desirable. The best option is to use strips of medium thickness, alternating with thinner or thicker ones.
If you have low ceilings, opt for vertical stripes. For high ceilings, horizontal stripes can be used. But you need to be careful, because if you do not want to completely strip the entire wall, but only a separate section of it, you need to abandon horizontal lines. Then the choice of alternating vertical stripes would be the best option.
It is important to immediately decide on the color scheme. Stripes can be either the same color or different. A very large contrast will give the room a variegation. Experienced designers recommend either choosing colors that are similar to each other, or staying with gradients. Whichever color you choose, a dark to light gradient will give the room a sense of lightness and mystery. And it always looks pretty cozy.
Back to the table of contents
Marking with lines
After that, you need to paint the wall in the main color, which will be the base color. It should also blend well with the stripe color. It is better to dwell on matte paint, and then make the stripes glossy - this way they will look more impressive. Leave the walls to dry for about three days.
Now you can start marking the walls for applying stripes.
It can be very difficult for beginners to correctly mark the striped wall, since in this work it is extremely important to make sure that all lines are fairly straight. Therefore, for marking, stock up on tools such as:
- roulette;
- chalk or pencil;
- masking tape;
- building level;
- plumb line;
- small ruler for small measurements.
First, estimate how many stripes you want to see on the walls. How thick should the stripes be? Then, from the top of the wall down, mark with a tape measure and chalk (pencil). Remember to use a plumb line if the stripes are vertical, or a building level if they are horizontal.
When the lines are drawn, it is necessary to glue masking tape along their edges. In this case, it must be applied so that the main lines, which will be painted in separate colors, are protected on both sides by strips of adhesive tape. This will keep them smooth and prevent paint from spilling onto nearby stripes.
It is important to follow several important rules when gluing tape. First of all, you need to try to firmly press the tape against the wall. It is good to use a spatula for this. If this is neglected, then the paint will fall under the tape. Then the lines you get with uneven edges. And it will be very difficult to fix it later.
The second rule is to protect the floor and ceiling well from paint stripes. For this, the joints are carefully glued with tape. This is especially important if the ceiling is already finished. It is difficult to fix the ingress of paints on the refined ceiling, so take care of protection in advance.
There are moments in life when the home environment radiates harmony and balance of feelings. Beautiful striped walls will tidy up emotions and reload the “matrix” of living space. For this to happen, you need to pick up paint, painting supplies and paint the walls.
Decoration, striped walls
It is known that striped walls are a popular way of decorating and decorating the walls of a room. The striped wall decor in the interior allows you to give rhythm and dynamics to the room, enlivening and drawing attention.
The attractiveness of the stripes is inherent in nature itself. We love the stripes of the magic rainbow bridge after the rain and the lively striped contrast on the skins of the animals.
So why not create a striped wonder in your apartment or private home. There is no doubt that the striped wallpaper from the manufacturer is the best option, but the walls can be painted with your own hand in the desired and correctly selected color.
At the same time, any striped wall design is created with the best intentions and possibilities. By the way, the technology for creating striped walls is simple and affordable. It remains to prepare sketches, make measurements and markings, purchase the necessary painting tools and hit the road, or rather, a striped flight.
Naturally, the starting point and route in the direction of how to paint the walls with stripes, we will consider the painting technology.
Striped wall painting technology
It is noteworthy that the basic technology for painting striped walls can be confidently applied to a flat and embossed surface. The strip looks equally attractive on a concrete base, on convex block house panels and walls with ledges or niches.
The main thing is to respect the proportions of the width of the stripes and apply the paint successfully. As a result, the question: "How to paint a striped wall" will be successfully resolved.
Wall painting technology consists of the following stages:
- creating a base background
- marking the surface into stripes (vertical or horizontal)
- masking tape to create stripe borders
- coloring the stripes with the required color
- removing the tape of adhesive tape.
Before starting the marking of the walls for painting, it is necessary to make a simple calculation of the whole number of stripes.
preliminary calculation of the strip width
To do this, we determine the width and length of the walls and divide by the width of the strips. You should get an integer, the number of whole stripes can be adjusted by increasing or decreasing their size. Adjustment of the dimensions of the width of the stripes can be made using stripes of light color.
base background
A prepared (putty) light-colored work surface can be used as a basic background for painting. The base tone can be created using matt acrylic paints that have excellent hiding power and are economical in the use of an odorless material.
surface marking
Armed with a level, a corner and a pencil, we break the wall into horizontal or vertical lines. For example, when creating a horizontal line on a surface for a wall in a horizontal strip, place and mark the width of the required stripes.
Then we apply a level vertically to the indicated landmarks and outline the lines corresponding to the edges of the stripes. Mark the future color stripes with a cross.
Similarly, we mark the surface for the wall in a vertical strip, creating a working vertical and marking the width of the vertical stripes.
masking tape sticker
The most practical material that can withstand a layer of paint and prevent it from penetrating inside is masking tape, which must be firmly glued to the surface.
features of masking tape
For stickers, it is preferable to use masking tape, which practically do not leave traces after removal and have a tenacious adhesive layer. The versatility of the adhesiveness of the adhesive tape allows you to select the tape depending on the type of surface and paint. There are masking tapes designed for professional contouring and pasting of surfaces with a carrier layer of smooth crepe, moisture resistant, capable of withstanding a stress of 75-80 g / m2 with a solvent-free adhesive.
Useful Tips
Select tape to create stripes, preferably according to their intended width. The most popular are considered tapes - scotch tape 50 mm wide. But the width of the strips can be combined by gluing two tapes of adhesive tape of different widths: 50 mm + 30 mm or 30 mm + 10 mm. The smallest paint throughput is possessed by tape on crepe and mylar base.
paint the walls with stripes
To paint over the stripes, select a narrow flat brush number 5-7 and a velor miniature roller on the handle. Apply selected paint such as Dulux Trade Vinyl Matt from top to bottom in one stroke of a well-filled roller. When applying paint, you can safely touch the edges of the glued tape with adhesive tape. After the initial layer of paint has dried, apply the next layer.
Then carefully remove the masking tape. Do you find it difficult to repair the question of how to paint the walls with stripes of different colors? Sketch the color sequence of the stripes and mark them on the wall. Initially paint all stripes in one color, then in another and leave to dry. For example, the pulsating combination of tangerine stripes with warm cinnamon and a binder color of delicate vanilla will provide the walls with a full imitation of expensive brand rasch wallpaper .
Useful Tips
The main tools for applying paint and creating a smooth painted surface are structural bead ... But of particular interest is creative line - rollers with nozzles that create a relief coating. The coating of the working part of the roller can be strips of leather pieces. In this case, the originality and effectiveness of painting will be guaranteed.
If for a flat surface the technology for painting stripes is clear - drive yourself up and down along the directly glued tape with adhesive tape, then for embossed surfaces, such as a convex and volumetric block house, the creation of stripes is somewhat complicated. It is now recommended to carefully stick masking tape on the convex part of the surface along the path of the stripes.
Then the convex part of the walls is painted over in the traditional way using a spray gun. After the paint has dried, the masking tape is removed.
How to paint walls with stripes will help the video.
