Plastic apron for the kitchen with photo printing. PVC panel apron in the kitchen. What is the plastic apron attached to?

19.10.202327.05.2017

PVC apron panels are a budget option and are used to protect and decorate walls. Due to the high cost, skinals are less common - tempered plexiglass with decorative design. Since panels are produced in different qualities, products made from ABS plastic are especially popular. A plastic apron can be purchased ready-made or made to order, and installation of the apron does not require specialized repair skills.

Due to the soft structure characteristic of polymers, this material is flexible, which avoids deformation during operation. When installation is carried out, the sheet is equally successfully cut with a table knife and a jigsaw. ABS panels in stores are presented in two standard formats: 601x3001 and 601x2001 mm with a thickness of 1.6 mm.

Opaque ABS plastic and similar products are decorated with a special film or using photo printing. Family photos and unique travel snapshots are displayed on the surface, and an exclusive gallery adorns the perimeter of the kitchen. Compositions of flora and fauna, motifs on the theme of nature are considered a priority. First, a design is selected from a photo from the catalog, then the membrane is applied to the skins.

Advantages of plastic kitchen aprons

Advice! An apron made of transparent polycarbonate is indispensable for small spaces. For example, ABS skins with a transparent watercolor pattern will visually expand the space. At the same time, you can install an LED strip under the skinali as a backlight; this looks especially good if the panels are fixed to the frame.

Disadvantages of a plastic apron:

Insufficient strength. After any dynamic load, a mark remains on the surface of the polymer;
For 3-5 years the material will retain its original appearance, but then the panel will begin to fade. Light-colored products turn yellow over time.

Important! A plastic kitchen apron is comparable in fragility to glass and requires careful handling. Products made from polycarbonate are characterized by a degree limit of +66 °C, so the hob should not be installed close to the wall.

The principle of attaching a plastic apron with your own hands

Do-it-yourself installation of plastic skins is done in several ways: with glue and lathing. Traditionally, a kitchen apron made of plastic is installed using classical technology - on slats. With any method of fastening, first of all the wall is carefully leveled.

Technological nuances

You can attach the panel with self-tapping screws, since the caps will be hidden behind the cabinets. If you need to assemble a kitchen apron from small segments of plastic - 30 cm in width, the modules are composed according to the principle of wall panels. The first strip is inserted into the lower profile. The second is fitted into the groove and secured with staples. One end of the fastening element clings to the frame, the other holds it. The following modules are installed identically. To ensure that not a single joint is noticeable, each plate is adjusted to the previous one with a rubber hammer. The finishing module snaps into the groove. Installing an F-profile will completely hide all the lines.

The disadvantage of this method is the free space between the sheet and the wall where mold can develop. The advantage is that the screen can be easily replaced if damaged. If you want your polymer apron to last a long time and not lose its attractiveness, you can pay attention to more expensive analogues, for example, glass skinals.

You can only glue an ABS plastic apron with liquid nails onto a perfectly flat wall. The glue is distributed in a dotted line over the surface where the polymer sheet is applied and pressed. The sheet is supported from above by spacers. At the corners and at the bottom it is additionally secured with self-tapping screws.

This installation method is simpler if the walls are smooth and no additional work is required to level them. The disadvantage is the inconvenience of dismantling and replacement.

A plastic apron is an opportunity to radically change the interior of your kitchen by adding bright colors to it. Many people in the reviews say that they installed a similar structure in the kitchen with their own hands. You can choose different types of plastic that will fit into the design of any interior - imitating natural materials, with photo printing, plain. You can also place your photos on the apron, which will make your kitchen space unique.

Plastic aprons for the kitchen and their types

An apron is a canvas that covers part of the wall in the kitchen. The coating is placed in the “working area” and serves to protect the wall from exposure to temperatures, accumulation of dirt, and also acts as an independent piece of furniture. The apron is mounted near the stove, sink, and also above the countertop.

Typically, aprons made of dense materials such as ceramic tiles, marble, wood panels or fire-resistant glass are installed in the work area. Recently, aprons made of plastic have become popular, which is much cheaper than other materials and at the same time reliably protects the surface of the wall.

The following types of plastic aprons are offered for installation:

ABS sheets. This material is sold in the form of plates from which the desired shape can be cut. Typically, ABS sheets are used if you plan to use photo printing. You can choose plastic with an image already applied or order an individual design, for example, place a high-quality photograph or a beautiful picture on the canvas.
PVC panels. They are sold with a pattern already applied, usually decorated with ornaments or plain. Plastic is quite popular, which imitates various surfaces - marble, wood, mosaic. They vary in panel thickness.
PVC lining. On the market you can find several types of such material, which differ in thickness. Usually produced in a single color in soothing pastel colors.

The choice of material should be based on its technical characteristics, as well as the personal preferences of the customer.

Advice. The thicker the plastic chosen for mounting the apron, the higher its strength and resistance to temperature.

It is worth noting that different types of plastic differ significantly in price. For example, PVC lining is much cheaper than other types, and the most expensive type is ABS sheets. You will also have to pay extra to add a personal design to the apron.

The main pros and cons of a plastic apron

Plastic aprons are installed in almost all modern kitchens. This popularity of the material is due to its positive qualities:

plastic is much cheaper than other materials that are used to install aprons;
easy to clean - just wipe the apron regularly with a soft sponge;
is not afraid of moisture, steam, and can also withstand high temperatures (up to 80 degrees);
does not require preparation of the wall surface before installation;
easy to install - you can install it yourself;

has many colors, which allows you to create a unique kitchen design;
the design on the plastic does not fade or fade even with prolonged use;
durable in use if properly maintained;
The apron can be easily removed if necessary.

With all the advantages of a plastic apron, it has a number of disadvantages.

The main disadvantage of plastic in the kitchen interior is the flammability of the material. Placing an apron in close proximity to open sources of fire may result in a fire. In this case, the plastic ignites in a few seconds and completely melts in 5 minutes. When burned, it forms toxic substances that are deadly to humans. Therefore, owners of gas stoves should place the apron at a distance of at least 20 cm from the fire. It is also recommended to separate the stove from the wall using a metal cover.
There are many models of low-quality plastic on the market, which usually costs much less, but at the same time has low technical characteristics. This material releases toxic gas when heated. To avoid buying a fake, be sure to ask the seller for a quality certificate.
The plastic apron does not tolerate impacts. When large objects hit the surface, small cracks and dents form on the plastic, and the design is damaged.
The material is subject to deformation due to exposure to abrasive substances, as well as detergents that contain acetone. Do not try to wash the surface with metal sponges, as cracks and scratches may form.

Of course, a plastic apron has more positive qualities than negative ones. If you properly care for the surface and also take the choice of material seriously, the apron will bring only positive emotions to the apartment owners.

DIY installation of a plastic apron

You can install an apron in the kitchen yourself or turn to professionals for help. For installation you will need a minimum set of tools and consumables.

The first thing you need to do is choose the type of plastic and its color. Having selected the material to suit the design of your kitchen, you can begin taking measurements.

Advice. In order to correctly measure the area of the canvas, it is necessary to carry out measurements with a margin. Part of the apron, approximately 20 cm, should extend beyond the wall cabinets and countertop. This way you can achieve maximum wall protection.

After selecting and purchasing plastic, you can begin its installation. Before starting work, you should treat the surface of the wall with a primer and let it dry a little. There is no need to level the wall before work. Installation is carried out in several ways:

attaching the apron to waterproof glue;
fastening the canvas using self-tapping screws;
installation of plastic on a pre-prepared structure.

The first method is the simplest - strips of glue are applied to the wall. First, the glue is applied around the perimeter, and then in horizontal stripes with an interval of 15 cm. Then pre-degreased plastic is applied to the wall. This installation method is the fastest, but has a drawback - it will not be possible to remove the plastic sheet without deformation.

Attaching the apron using self-tapping screws is also not difficult. For reliable fastening, four self-tapping screws are sufficient, which are located around the perimeter of the canvas.

If the kitchen wall is uneven, a plastic apron can be attached to an aluminum profile. In this case, aluminum or wooden slats are first attached to the wall, and then an apron is mounted on them.

After installation is complete, holes are cut out on the apron for sockets, wires and pipes.

Thus, a plastic apron is an economical and easy way to decorate your kitchen.

Installation of a plastic kitchen apron: video

Plastic apron: photo

The classic solution is a tile backsplash, but not everyone finds the design to their liking. In addition, installation is a troublesome task.

It’s much easier with aprons made of MDF, wood and even metal. But all these materials are inferior to plastic in terms of cheapness and ease of installation.

1. Types of plastic

PVC plastic is highly rigid and durable, it can be painted and varnished, and is also very resistant to fire. The price is relatively low. In addition, its installation can be done on your own.

Polycarbonate aprons are the most durable and resistant to various types of damage, but they are also the most expensive type of plastic. As a rule, people come for such an apron purposefully; it is not as popular as PVC. But it is impossible for an untrained buyer to visually distinguish between these two plastics.

2. Advantages and disadvantages

Advantages of plastic:

It is resistant to moisture,
the holes required for sockets can be easily cut out in it,
Installation on the wall will not take much time.
Choose style and color will not be difficult even for the most sophisticated kitchen. Polycarbonate, in addition to the above advantages, is characterized by resistance to high temperatures and even aggressive household chemicals.

Review by Ksenia Vorontsova: I have a plastic apron in my kitchen. In principle, I am satisfied with it. It is easy to care for and can be cleaned with regular cleaning products. The only negative is that it is not as beautiful as glass with a pattern.

The disadvantages include some difficulty in care:

Water stains form on the surface
PVC scratches quite easily and scratches will be noticeable
PVC can be deformed due to high temperatures.

Review by Igor Shkurny: I had a plastic one... I installed it temporarily because I had nothing to do.. to be honest - it’s fucking rare. Firstly, all these corners, and secondly, the fragility of the plastic. Now there is a table instead of a panel (I got it on a ball). I like it, it’s durable and practical, but in general it’s done either with TILES or a wall panel.

3. Installation

Installation does not require any special skills, but the presence of some tools - yes. The choice of installation method depends on the curvature of the wall:

If the wall is absolutely flat, the apron can be attached with glue. However, the glue will leave marks on the wall and on the plastic itself; removing and hanging the panel again will not work. When choosing this installation method, special attention should be paid to surface preparation. After removing the old coating, all cracks and crevices need to be sealed and the wall primed.

Tools and materials: mounting adhesive, building level and tape measure.

An easier installation method is using self-tapping screws. Before installation, the surface must be leveled, however, the same care as when installing with glue is not required. Then you can start installation. After completing the work, the screw heads must be closed with decorative plugs, and the edges of the apron must be covered with baseboards or other elements.

Tools and materials: hammer drill or impact drill, screwdriver or screwdriver, self-tapping screws, decorative plugs and baseboards, as well as a building level and tape measure.

Using self-tapping screws on the sheathing - in this case, the wall does not need to be specially prepared at all. It is enough to make a sheathing and install an apron on it. Further actions are similar to the second method.

Tools and materials: hammer drill or impact drill, screwdriver or screwdriver, material and equipment for creating sheathing, decorative caps and baseboards, as well as a building level and tape measure.

4. Photos and prices

Unfortunately, all our attempts to find real photos of plastic aprons with prices ended unsuccessfully. Manufacturers and sellers persistently prefer to post photographs of samples rather than finished work on the Internet. And, as a rule, these samples involve photo printing.

Cost of 1 p.m. 60 cm wide (standard size) from 20 to 50 dollars.

PVC plastic apron with photo printing measuring 2x0.6 m for about $50

An apron for a kitchen set is a useful and even necessary interior detail. It can be not only ceramic, but also plastic - let’s take a closer look at this option.

A sink for washing dishes, a cutting table, a gas or electric stove - most often these kitchen elements in our apartments are located along one wall. During the cooking process, splashes of water, steam and fat inevitably fly from the sink and stove, and the process of cutting food leaves noticeable marks. Therefore, the wall adjacent to the sink, stove and table can quickly lose its presentable appearance.

For this reason, the kitchen workspace is usually decorated with a so-called apron. This element is a large “overlay” that should protect the surface of the wall. The apron is always made of material that is resistant to moisture and is easy to clean from dirt.

Undoubtedly, a ceramic tile backsplash remains a classic option. However, it has the highest cost - and during the repair process you really want to save money. A good alternative could be a panel made of high-quality plastic - durable, beautiful and inexpensive.

A plastic apron is made from polymer materials - polycarbonate or polyvinyl chloride. Plastic models come in a wide variety of textures and patterns and can be either glossy or matte. In terms of their characteristics, they are not inferior to ceramics - and in some parameters they even surpass it.

Advantages of a plastic apron

What are the advantages of a plastic apron for the kitchen wall?

First of all, this option is extremely low cost. The issue of price becomes especially important when it comes to a spacious kitchen, where it is necessary to cover a significant section of the wall with an apron. To lay it out with tiles would require a lot of expense - but plastic allows you to spend a minimum of money.
Plastic models have an attractive appearance. Thanks to the variety of design options, you can choose an element that will fit perfectly into the kitchen interior - and will look solid and aesthetically pleasing. It is a mistake to think that plastic looks cheap - modern technologies make it possible to create very beautiful and sophisticated products.
The apron collects a minimum of dirt and is easy to wash. Streaks and stains from water, droplets of grease, sediment from evaporation - all this is quickly removed from the plastic surface with an ordinary damp sponge. Plastic can be washed using household chemicals - the material will not be damaged, the main thing is not to use abrasive powder products.
The seams between the panel components are very small, almost invisible. Therefore, even after long-term use, they do not become clogged with dirt.
Plastic tolerates difficult operating conditions well. It calmly reacts to high humidity, does not deform from temperature changes, and does not fade from sunlight.
The plastic panel is easy to install. To accurately fix ceramic tiles, you must have repair skills - in addition, the tiles take a long time to dry. The plastic is installed with your own hands in a couple of hours - you can use the kitchen right away, without a long wait.

The disadvantages of such models include only the sensitivity of the material to abrasive influences - however, almost all materials have a similar disadvantage. In order for the plastic to retain its presentable appearance for a long time, it is enough just not to scratch it and not to use powders when cleaning.

How to attach an apron to the wall?

How exactly is a plastic apron attached to the kitchen wall? There are four main methods - all of them are convenient and quite simple. Let's take a closer look at each of them.

On special profile guides

As already said, a plastic apron is a very inexpensive purchase. Therefore, many people prefer to experiment with design, replacing the panel with a new one from time to time. If you suspect that in a couple of years you will want to refresh the interior, then it is best to mount the cladding on the profile guides - this way you can freely remove the covering without damaging the wall.

The guides are special metal slats that are fixed horizontally to the wall surface using self-tapping screws. The plastic sheet is simply installed on the guides, like on a kind of “rails” - and, if necessary, is pulled out and replaced with a new one.

Self-tapping screws to the wall

If you are choosing kitchen cladding for years to come and are not going to change it without good reason, then you can immediately use self-tapping screws - plastic can easily be drilled through. This installation method requires the most even rough surface - but it will be very convenient if behind the apron there is an expensive decorative coating that you don’t want to spoil with metal slats and especially glue. It is easy to disguise traces of screws on the surface of the plastic - simply by placing plugs that match the color.

By the way, with this installation method, the plastic panel does not fit flush against the wall - a small space remains behind it. If desired, you can hide electrical wiring under the apron. In addition, the self-tapping apron is also easy to remove.

On the sheathing

If the kitchen space is quite spacious and a wide section of the wall needs to be covered with an apron, many people prefer to save effort - and install the cladding directly on the rough wall without decorative finishing. In such cases, the wall is not always perfectly flat - however, this can be easily corrected with the help of lathing.

The sheathing consists of several metal slats or wooden blocks attached to the wall along the perimeter of the future apron. First, a kind of square is created on the wall, matching the size of the apron. Then additional horizontal and vertical strips are fixed inside it with self-tapping screws, giving the structure greater stability and strength. A plastic panel is attached to the resulting sheathing, also with self-tapping screws. There is some space left between the apron and the wall where you can lay electrical wiring or, for example, make lighting.

On glue

Finally, the easiest way to install siding is to glue it down. It is best to use liquid nails. The glue is applied in thin strips at a short distance from each other, and then the plastic panel is pressed on top.

The main advantage of the method is speed and ease of installation. But it must be taken into account that the plastic panel can only be glued to a perfectly flat wall. If the surface has even slight differences in height, the apron will not attach well and may quickly fall off.

Cost of a plastic apron

How much does a plastic apron cost? The exact price always depends on the material and decorative design of the apron. For example, polycarbonate is cheaper than polyvinyl chloride; a panel with a uniform texture will be cheaper than a panel made to look like marble or wood.

On average, the cost of a plastic apron is about 1,500 rubles. When choosing a panel, it is not recommended to consider overly cheap models - they may turn out to be of lower quality and durability.

External variety of plastic aprons

What design possibilities does a plastic apron provide when installing it in the kitchen? The appearance of the panels is very diverse. The simplest variety can be called ordinary plain aprons or PVC panels that imitate lining. But if you want to create a truly unusual design in the kitchen, then you should pay attention to aprons with a pattern or artistic texture.

Plastic aprons designed to look like tiles, mosaics, natural stone or wood are very popular. This surface quite convincingly imitates granite and marble, wood, colored glass, and brick.
An interesting variety can be called models with a colored pattern. The image is applied in two ways - it can be extruded on the plastic itself or on a film, which is a decorative layer of a plastic panel. The options for drawings are truly endless - they can be flowers, natural or city landscapes, still lifes and much more.
The plastic apron can have a glossy or matte surface. What to choose depends on personal preferences. However, keep in mind that you will have to take more care of the shiny surface - dried water splashes and droplets of grease will be especially noticeable on it.

In general, a plastic apron fits perfectly into any interior and in appearance is practically no different from more expensive materials. If you are looking to save money on home renovations, this design option can be a real godsend for you.

Tell

Plastic aprons for the kitchen are becoming increasingly popular. The reason for this is the price-quality ratio. For example, a kitchen apron made of plastic with photo printing will cost several times less than a similar apron made of tempered glass (). Ease of installation also plays a role, because you can install such an apron yourself, avoiding additional costs.

Plastic, or resin, is a synthetic material made from polymers. Polymers are produced synthetically, and at the same time they set the desired properties, producing plastics for various purposes. Kitchen aprons made of plastic are mainly made from several types of plastics, differing both in properties and in price.

Types of plastic for aprons in the kitchen

ABS

ABS plastic is produced in the form of granules, transparent or colored. They are molded into flat sheets of size 3000x600x1.5 mm or 2000x600x1.5 mm. This is a very shock and bending resistant material. If the temperature briefly rises to 100 degrees, it will not catch fire, but 80 degrees can withstand for a long time, so ABS kitchen splashbacks are fireproof. This plastic can be coated with a metallized coating - then it will look like a mirror, but the weight and installation of products made from it is much lighter than from mirror glass.

The main advantages of the material:

Resistant to aggressive liquids and environments;
Does not deteriorate when interacting with fats, oils, hydrocarbons;
It can have both a matte and shiny surface;
Wide variety of colors;
Non-toxic;
Can be used at temperatures from -40 to +90.

Disadvantages of a kitchen apron made of ABS plastic:

Fast fading in sunlight;
When acetone or solvents containing it come into contact with the surface, the plastic dissolves and loses its appearance;
The material has a yellow tint.

Acrylic glass (polycarbonate)

Produced in the form of sheets with dimensions 3000x600x1.5 mm and 2000x600x1.5 mm. In many respects, this material is superior to glass - it is more transparent, can withstand even strong impacts, while it has a low specific gravity, and is easier to mount on the wall in the kitchen than glass.

Advantages of a polycarbonate kitchen apron:

High transparency;
Resistance to impacts and bending;
Fire resistance;
Does not fade or fade in the sun;
Fire safety: does not burn, but melts and solidifies in the form of threads, does not form toxic substances during combustion;
Does not release substances hazardous to health into the air even when heated;
It has an attractive appearance and is practically indistinguishable from glass.

The only negative is the rather high price of the product compared to other types of plastic aprons, but it is still much cheaper for the kitchen, although it is superior in some respects.

PVC

Polyvinyl chloride has long been widely used in finishing work, and not only in the kitchen. Most often, kitchen panels for plastic splashbacks are made from this material. This is a fairly budget option, which has its pros and cons.

Finishing materials are available in several types:

Panels: up to 3000 x (150 - 500) mm;
Lining: up to 3000 x (100 - 125) mm;
Sheets: (800 - 2030) x (1500 - 4050) x (1 - 30) mm.

PVC is the most budget option, and also the fastest - installation does not require preliminary surface preparation and can be done on your own.

Advantages of using PVC for the production of plastic aprons:

Easy to install and maintain;
Resistance to elevated temperatures and humidity;
Variety of design solutions: plastic can have any colors, volumetric details, prints or be transparent.

Disadvantages of a PVC kitchen apron:

Low abrasion resistance;
Rapid loss of strength;
Rapid loss of appearance under the influence of light and detergents;
Water can get into the cracks between the panels, resulting in suitable conditions for the formation of fungus and mold;
Low fire safety: does not withstand contact with fire;
May release substances hazardous to health into the air.

Not all panels have this last drawback, so when purchasing, you should ask for a quality certificate and make sure that the chosen option is safe.

Plastic provides the widest possibilities for design, since products made from it can have almost any color, interesting texture, relief surface, drawing or photograph, applied using photo printing. The only problem is to choose the option that suits your interior.

Color

Plastic can have any color and shade - from pastel, light tones to thick, rich colors. Colors are selected based on the chosen interior style and the size of the kitchen. Light colors will help make the kitchen visually larger, while dark colors will “shrink” the room.

The kitchen apron area is the most “dirty” place in the kitchen, so pure white or black is hardly appropriate here. In calm pastel colors, drops of water and other dirt are not so noticeable; the panels do not have to be wiped several times a day.

Drawing

Almost any design can be applied to plastic - its choice depends only on your imagination and design requirements. Small patterns will help make accidental stains less noticeable; they are suitable for small kitchens. In a large room you can use large patterns and designs.

Imitation of natural materials

Plastic panels that imitate natural finishing materials are very popular. They save not only money, but also time during repairs. Laying brickwork or porcelain tiles is expensive and takes a lot of time; installing a panel “under brick” or “under porcelain tiles” can be done on your own and takes only a few hours.

Plastic can imitate ceramic tiles with or without a pattern, popular “hog” tiles in different colors, wooden or stone surfaces. Imitation materials are applied to plastic using photo printing.

Photographic images of various scenes on kitchen aprons are gaining popularity. They make it possible to make the kitchen more interesting, give it exclusivity, photographic pictures remind of favorite places, summer holidays, transfer them to the garden with exotic flowers or add delicious fruits to the kitchen decor.

Kitchen aprons made of plastic with photo printing cost much less than similar ones made of glass. The cost of installation is also lower, and, in addition, the opportunity to change something in the kitchen remains. After installing it, it is no longer possible to make a hole in the glass apron to hang, for example, a rail that is needed, or a shelf for spices. Plastic allows this. Moreover, at first glance, the glass skinal is practically indistinguishable from a kitchen apron made of plastic with photo printing.

Making the kitchen not only cozy, but also beautiful is the desire of any housewife, and if saving money, effort and time is an important factor, then a plastic kitchen apron is an excellent option. It does not require special skills to install or replace, and with proper care the product will last at least 5 years.

What is a plastic apron?

A plastic apron is made from polymer materials such as polycarbonate or polyvinyl chloride (PVC). Despite the relatively low cost, light weight and flexible structure, a kitchen apron made of plastic is durable, able to withstand high temperatures (up to +120°C), and is not susceptible to the development of mold and the proliferation of microorganisms.

There are 3 types of materials for an apron:

Solid plastic sheets 1.5 cm thick and 60 cm high. The length of such plates can be 2-3 m. The product can be glossy or matte, has a smooth or structured surface, and is decorated with drawings and photo printing.
PVC panels are produced with a thickness of no more than 1 cm, width varies from 15 to 50 cm, available lengths are 260, 270 and 300 cm. They are printed with designs and embossed to resemble wood, tiles, and mosaics.
PVC lining - three-meter strips 10-12.5 cm wide, most often plain, in pastel colors.

Advantages of a plastic apron

If we consider the pros and cons of a plastic kitchen apron, then there are many more positive aspects:

An affordable price allows you to get high-quality results without high costs. This option is perfect for tenants, low-income families, and people who want to constantly change their interior.
Installing an apron in the kitchen with your own hands does not require any special knowledge, skills or special tools. Even a woman can handle the installation process. There is no need to level the walls, no need to wait for drying. This is the best solution for quick repairs.
The variety of structures, surfaces, and colors makes it possible to complement or improve the existing interior design. If desired, you can place any drawing on the panels, even a family photo.
The smooth surface and absence of visible seams simplify maintenance. It is enough to use any detergent and a napkin to make your apron shine clean and shiny.
The low weight of plastic, unlike ceramic tiles and glass, makes it possible to install it on interior partitions. This is the only available option when planning small apartments or dorm rooms.

Disadvantages of a plastic kitchen apron:

The strength of the material is quite high, but you should not subject it to strong mechanical stress: scratches or cracks may appear over time.
There is a possibility of purchasing a low quality product. It is necessary to carefully check the quality certificate and pay attention to the strength of the internal partitions.
Despite its high thermal stability, plastic is susceptible to melting and burning. It must be protected from open fire.

Before installing a plastic apron, you need to decide on a color or pattern and calculate how it will fit into the style of the interior. You can order the application of the selected image. For those who like to create interior items with their own hands, there is the opportunity to purchase a transparent plastic apron, which at home and in the hands of a craftsman will turn into an original decoration of the kitchen wall.

Decorative painting

The most common method of decorating a plastic apron is painting: drawings and patterns of various themes are applied to the back of the finished product, either by hand or using stencils. The kitchen will be decorated with a full-fledged painting or a stylistic panel, which just needs to be attached to the right place. To avoid fading in the sun or under the influence of temperature, it is better to use oil or acrylic paints for drawing.

To emphasize the uniqueness of such an apron, it can be secured with eye-catching fasteners or special frames purchased at a furniture store.

Photo wallpaper

An easier way to decorate a plastic apron is by gluing photo wallpaper. As a result, the working wall will be decorated with a seascape, a forest clearing, a view from a window, or a fruit and vegetable still life.

Before gluing, you should make sure that the surface of the plastic is clean, since even the slightest specks of dust will form an air bubble and deform the overall pattern. For gluing, use special silicone transparent glue in jars or a spray, which is applied to the front surface of the picture, then carefully attached to the back of the panel, and the photo appears under the plastic.

Film

A common decoration method is the use of self-adhesive film. Depending on your preferences, you can use ready-made colors and a variety of patterns, or you can order photo printing to order. Gluing the film requires care and patience. The protective paper is removed gradually and the surface is carefully smoothed. For convenience, the surface of the plastic is sprayed with water, which will be removed during smoothing.

The big advantage of this method is that with the help of film you can update the facade of the kitchen, creating a single composition.

Preparation of plastic panels, layout and cutting

The most important stage of installing a plastic apron is the creation of blanks from which the working wall will be formed in the future.

To begin with, measurements are taken of the desired final product, taking into account the method of fastening, the presence of overhangs of furniture or the exact fit between the desktop and hanging cabinets.

The easiest way is to use OSB sheets. Their height completely fills the working wall; you only need to cut off part of the required length.

When using panels and lining, it is best to mount the pieces vertically, using short, narrow pieces. Before you start attaching the pieces to the wall, you need to stack them on the floor. This is a check that will allow you to see the finished dimensions and the size of possible miscalculations.

For cutting, use a fine-toothed hacksaw or carpenter's knife and a long metal ruler.

How to attach an apron to a wall

Installation of a plastic apron depends on whether the kitchen renovation is completed, whether furniture is installed and what quality the wall is. Depending on the circumstances, the following fastening methods are used:

gluing directly to the wall;
fastening with self-tapping screws;
installation on a pre-assembled sheathing;
insert into a structure made of guide profiles.

It must be taken into account that the tabletop and the apron do not fit tightly enough to each other. To eliminate gaps and protect the rear parts of the furniture, use an angular plinth to match the color of the working wall or surface. The extreme sections of sheets or lining are hidden with plastic corners. You can use leftover laminate flooring.

Self-tapping screws to the wall

The easiest installation method is to secure it to the wall with self-tapping screws. The wall must be relatively flat so that the sheet does not deform.

For installation with self-tapping screws, select a kitchen apron from a single sheet. The part is pre-cut to the required size, and the edges are decorated and smoothed. The finished structure is applied to the wall, leveled if necessary and simply screwed into the corners. Fasteners can be hidden with special caps or painted over with paint to match the apron.

This method allows you to easily dismantle the plastic kitchen apron, but reusing it will be impossible.