 | The air heating system for the house is a complex climate system with partial air recirculation, due to which, along with heating, a constant supply of fresh air to the house is carried out to ensure ventilation of the premises. To organize heating in the house, an air heater is installed and a network of supply and return air ducts is laid to distribute air throughout the premises of the house. No traditional water heating system will allow you to solve a complex of climatic problems at once, therefore the price of air heating for a private house is quite justified and in most cases will be significantly lower than for heating, ventilation and air conditioning systems separately.
|
Hangar heating very difficult to accomplish with traditional fluid systems, as hangars tend to be large in volume and central heating just doesn't do the job. And installing your own boiler house for heating the hangar is not economically feasible. The use of electric heaters will also be very expensive during operation. We have equipment that allows us to properly heat the hangar, quickly and economically. Hangar air heating is the smartest way to maintain the optimal temperature in the hangar all year round. If you need to heat the hangar, please contact us. We can heat your hangar at minimal cost and save you money not only when buying and installing equipment, but also during its operation. The autonomous heating system using a gas air heater is the most reliable today. Even if it is not possible to connect to the central gas network, you can install a tank for liquefied gas, which will pay for itself very quickly, because gas is by far the cheapest and most economical type of fuel. The principle of operation of our hangar heating system is very simple.Air heaters are hung around the perimeter of the hangar, gas is supplied to them, a chimney is installed and a thermostat is connected, which monitors the temperature in the hangar. The desired temperature is set on the thermostat. When the temperature drops from the thermostat, a signal is sent to the control system of the air heater, the gas valve opens and the burner lights up. At the same time, the fan is turned on, which blows air through the heat exchanger. Warm air enters the hangar, and the temperature is brought to the set value. The thermostat sensor trips again and the system shuts down. This hangar heating system is completely autonomous and economical, gas is consumed only when the air heater is running. Hangar heating With high efficiency ovens, Modine minimizes costs through low equipment costs, low energy consumption and no operating costs. We supply this and other equipment for efficient hangar heating directly from the manufacturer, so our prices are minimal. The most popular Modine gas ovens are always in stock in our warehouse in Moscow. We will independently carry out the hangar heating project and carry out the installation with high quality and in the shortest possible time. No one will make you a better offer. Back to In winter, it is necessary to heat the warehouse if people work there for more than 2 hours without a break and their work does not equate to street conditions, as well as if it is required by technological standards for storing goods.
All warehouse heating systems can be divided into two large groups:
Central systems serve to heat the entire building, and heat is generated in one part of it and carried by heat carriers. The following can be cited as an example of a central heating system for warehouses: there is a separate boiler room that produces heat, heats water in pipes laid throughout the building.
The locals are different. They combine all its nodes in one device, and heat is generated and distributed in the room in which they are located. For example, heat guns or stoves. Which warehouse heating system to use depends on a number of factors: the volume of the room, the height of the ceilings, the technological aspects of product storage, the number of employees, the heat loss of the building, and the temperature outside.
Heating of warehouses of different categories
There are several classifications of warehouses, one of the most frequently used is the Knight Frank system. All warehouses are divided into categories, there are 5 of them: "A +", "A", "B +", "B", "C" and "D". You can calculate storage heating based on these categories.
These are one-story buildings, most often of a rectangular shape, built of sandwich panels and light metal structures with a built-up area of 40-45%. Can be made with or without columns.
Warehouse features:
- ceiling height from 13 m;
- automatic gates (at least 1 per 500 sq. m).
The building should have office and auxiliary premises, a ventilation and control system, an autonomous power plant, platforms for maneuvering heavy vehicles and, of course, heating.
Warehouse heating solution – air, water or steam heating. Moreover, if water acts as a heat carrier, then its temperature should be 150 ° C, for steam - 130 ° C. However, in rooms with the release of combustible dust and aerosols, a maximum of 110 ° C is allowed (SNiP 2.04.05-91). To heat the coolant, a boiler is used - gas or liquid fuel, placed in a separate boiler room.
For heating large warehouses, heat generators will be effective. Their installation is affordable. As for fan heaters, they cannot be used in rooms where combustible dust is present and there is the release of toxic aerosols: their small particles will be carried by air currents throughout the room.
One-story building constructed of sandwich panels and steel structures with or without columns and building area of 45-55%.
Warehouse features:
- ceiling height from 10 m;
- concrete floor with a load at a distance of 1.2 m 5 tons per square meter;
In addition to technological premises, there are also office and auxiliary premises.
To heat the building, air, water or steam heating of the warehouse is used with a water temperature of 150 ° C and steam of 130 ° C. To use it, boiler room equipment is required. In rooms with a large number of racks, heat generators can also be installed - they do not allow air to stagnate. Heat generators can be installed outside the building. Electric heating of the warehouse can also be applied. However, it is more often used for local heating of individual premises, for example, offices.
The building is one-story, mostly rectangular in shape with a built-up area of 45-55%, office and auxiliary premises. Can be reconstructed for storage.
Peculiarities:
- ceiling height from 8 m;
- concrete floor with a load at a distance of 1.2 m 5 tons per square meter;
- automatic gates (at least 1 per 700 sq. m.).
Air, water or steam heating can be used, implemented using a boiler room, heat generators, fan heaters.
One-, two-story buildings, possibly after reconstruction for a warehouse. If there is a second floor, then there must be elevators with a carrying capacity of 3 tons, one for every 2 thousand square meters. m. The building has auxiliary premises, office space is also possible.
Peculiarities:
Heating solution: centralized heating implemented with the help of a boiler room. Steam or water can be used as a heat carrier. Air heating using heat generators is not excluded.
Industrial one- or multi-storey building. Possibly an insulated storage hangar. Auxiliary and office premises are optional. When calculating the heating of a warehouse, the characteristics of the premises are taken into account.
Peculiarities:
- ceiling height from 4 m;
- asphalt or concrete floor without additional coating.
The best option for heating the hangar will be water or steam heating. Gas can be used as fuel for the boiler room if there is a highway nearby, diesel fuel or used oil. The latest energy carrier option is the most economical for industrial premises.
Unheated basements, civil defense facilities, hangars of any size. Do not require heating.
For a warehouse of any type, central air, water or steam heating is suitable. The exception is buildings that do not require heating.
You can choose the best option for warehouse heating and make an accurate calculation of warehouse heating by contacting Airvec. We will calculate the most economical option based on the needs of the building.
How to choose +
+
+
+
Of course, the approach to designing the heating of hangars differs from the heating of residential premises. Hangars are distinguished primarily by their large areas. The choice of hangar heating system depends on what will be stored in it. It is better to entrust the development and installation of the heating system in the hangar to a professional, however, it is important to determine the category of the room in terms of fire and explosion hazard and in the SNiP 41-01-2003 appendix to find which heating systems can be used. If the hangar is insulated, you can try heating registers placed around the perimeter. An inexpensive option, however, requires constant maintenance and monitoring. You can use fan heaters with thermostat control. Often they are placed under the ceiling, thereby providing air circulation. Water panels are the safest in terms of fire and explosion safety. Radiant panels on gas or electric should not be used for hangars with fuel, for example. For hangars with a high risk of fire and explosion, it is imperative to make fire-fighting exhaust fans. Usually hangars need a temperature of 15-17 °C, in some cases 5 °C is enough. +
+
+
Gas autonomous boilers +
+
+
+
Conventional liquid heating systems are not suitable for heating hangars, primarily due to the fact that hangars have a large area and height. It is problematic and inexpedient from a financial point of view to build boiler houses for them. Electric heaters consume a lot of electricity and are not economical. As an option in such a situation - air heating of the hangar, which will heat it quickly and economically. Gas heaters are more economical than electric ones. Even if there is no centralized gas supply, you can use gas in cylinders. Gas heating in the hangar is carried out according to the following principle: Air heaters are installed around the perimeter in the hangar, a gas source and a thermostat are connected to them, the thermostat regulates the temperature, when the temperature drops below the set value, a signal enters the control system, ignites the gas burner and turns on the fan that drives warm air through the system. The hangar is heating up. When the temperature rises to normal, the thermostat will turn off automatically again. In this case, you need to organize a chimney. The advantage of such heating of the hangar is that the gas is consumed only when the thermostat is activated, so the gas is consumed sparingly. +
+
+
Infrared heaters +
+
+
+
Practice shows that heating in the hangar can be effectively performed by infrared heaters. They are economical and safe. The space is heated using infrared radiation. The temperature in the hangar can be adjusted using a thermostat. Infrared heaters are easy to install and operate. This method of heating is applicable to any ventilation system. During operation, infrared devices do not cause air circulation, and dust does not rise in the hangar. Infrared heaters effectively heat the hangar. Infrared rays do not heat the air, but the objects and surfaces around, then the heat is transferred into the air. Thanks to this mechanism, heat leakage to the street through doors and cracks is minimized. Infrared heaters can be placed on the ceiling, walls, floor. A variant is possible when heating is regulated in different parts of the hangar, for example, in one part, heating can be completely turned off or the heating temperature can be reduced.
Every normal person wants information: what to do to improve the system at home. Absolutely anywhere in the Russian Federation there is a need to heat the house during a special period. It is difficult to imagine the existence of a person in Russia without heating the house. You may be aware that fuel for heating is constantly becoming more expensive. The Internet site hosts many home heating systems that use completely different principles for extracting heat. The published heat generation systems can be implemented individually or in a hybrid way. Aviation HangarAircraft hangar scheme Hangar - a special room for parking, maintenance and repair of aircraft, airships, helicopters, other aircraft, as well as any other large equipment. Hangars are also called any industrial premises of arched or tented type. The hangar is a prefabricated building. Depending on the technology used, hangars can be frame and arched. During the construction of frame hangars, load-bearing metal structures are mounted, and metal sheets are laid on them. There are also frame tent hangars covered with PVC fabric. The arched hangar is made of a special corrugated metal profile. At military airfields of fighter and attack aircraft, capital hangars, the so-called arched reinforced concrete shelters, are used.
Today, hangars have a very wide range of applications, they can be office buildings, shopping centers, warehouses, car services. 
Airship class PD-360 being taken out of the hangar Source: http://www.vonovke.ru/s/angar 
Owners and tenants of warehouses and hangars often face various problems. One of the most common and important heating. Most often, difficulties with heating arise due to the considerable remoteness of the object from central heating networks or due to high prices for connecting to them. And then the question arises of creating an autonomous heating system. Heating of warehouses, production, hangars for various purposes, where necessary Maintaining positive temperatures is a voluminous and serious task. There are many questions. What type of heating is best suited for this facility? What type, what manufacturer? How to choose heating equipment, how to calculate the required power, the number of heating devices for a given area? The housings of Icoline infrared heaters are made of steel, not aluminum, which allows you to minimize unnecessary losses, thereby increasing usefully directed energy. Ceiling heaters Icoline, unlike similar models from different manufacturers present on the infrared heating market, have stiffeners. Compared to "spineless" heaters, our heaters will not deform after the heater is in operation. Installation of infrared heating systems in hangars, industrial premises, warehouses. Installation of an infrared heating system will not cause any particular difficulties and large additional material costs. But despite the ease of installation, it should be done by professionals. Many years of experience and high qualification of our specialists allow us to quickly and efficiently carry out the installation of infrared heating systems. Over the years, our specialists have helped to solve the problem of heating in a large number of industrial and residential facilities. Fulfilling orders for the installation of infrared heating systems not only from Icoline, but also from third-party manufacturers such as Peony, Baloo, Mister Hit, Bilux and others. 
You have questions? Are you interested in something? Call us! And we will answer your questions, help with the choice of the necessary equipment. We will help you calculate the required number of infrared heaters, select the equipment you need for this. Why do we have!? We can offer you products manufactured by our company Icoline. Our company has a wide range of infrared heaters and you can choose and purchase what is most suitable for your production, warehouse or hangar. Source: http://ik-m.ru/auxpage_700/ In winter, it is necessary to heat the warehouse if people work there for more than 2 hours without a break and their work does not equate to street conditions, as well as if it is required by technological standards for storing goods. All warehouse heating systems can be divided into two large groups: Central systems serve to heat the entire building, and heat is generated in one part of it and carried by heat carriers. The following can be cited as an example of a central heating system for warehouses: there is a separate boiler room that produces heat, heats water in pipes laid throughout the building. The locals are different. They combine all its nodes in one device, and heat is generated and distributed in the room in which they are located. For example, heat guns or stoves. Which warehouse heating system to use depends on a number of factors: the volume of the room, the height of the ceilings, the technological aspects of product storage, the number of employees, the heat loss of the building, and the temperature outside. Heating of warehouses of different categories There are several classifications of warehouses, one of the most frequently used is the Knight Frank system. All warehouses are divided into categories, there are 5 of them: "A +", "A", "B +", "B", "C" and "D". You can calculate storage heating based on these categories. These are one-story buildings, most often of a rectangular shape, built of sandwich panels and light metal structures with a built-up area of 40-45%. Can be made with or without columns. Warehouse features: - ceiling height from 13 m;
- automatic gates (at least 1 per 500 sq. m).
The building should have office and auxiliary premises, a ventilation and control system, an autonomous power plant, platforms for maneuvering heavy vehicles and, of course, heating. Warehouse heating solution – air, water or steam heating. Moreover, if water acts as a heat carrier, then its temperature should be 150 ° C, for steam - 130 ° C. However, in rooms with the release of combustible dust and aerosols, a maximum of 110 ° C is allowed (SNiP 2.04.05-91). To heat the coolant, a boiler is used - gas or liquid fuel, placed in a separate boiler room. For heating large warehouses, heat generators will be effective. Their installation is affordable. As for fan heaters, they cannot be used in rooms where combustible dust is present and there is the release of toxic aerosols: their small particles will be carried by air currents throughout the room. One-story building constructed of sandwich panels and steel structures with or without columns and building area of 45-55%. - ceiling height from 10 m;
- concrete floor with a load at a distance of 1.2 m 5 tons per square meter;
In addition to technological premises, there are also office and auxiliary premises. To heat the building, air, water or steam heating of the warehouse is used with a water temperature of 150 ° C and steam of 130 ° C. To use it, boiler room equipment is required. In rooms with a large number of racks, heat generators can also be installed - they do not allow air to stagnate. Heat generators can be installed outside the building. Electric heating of the warehouse can also be applied. However, it is more often used for local heating of individual premises, for example, offices. The building is one-story, mostly rectangular in shape with a built-up area of 45-55%, office and auxiliary premises. Can be reconstructed for storage. - ceiling height from 8 m;
- concrete floor with a load at a distance of 1.2 m 5 tons per square meter;
- automatic gates (at least 1 per 700 sq. m.).
Air, water or steam heating can be used, implemented using a boiler room, heat generators, fan heaters. One-, two-story buildings, possibly after reconstruction for a warehouse. If there is a second floor, then there must be elevators with a carrying capacity of 3 tons, one for every 2 thousand square meters. m. The building has auxiliary premises, office space is also possible. Peculiarities: - ceiling height from 6 m;
- asphalt or concrete floor without additional coating.
Heating solution: centralized heating implemented with the help of a boiler room. Steam or water can be used as a heat carrier. Not excluded. Unheated basements, civil defense facilities, hangars of any size. Do not require heating. For a warehouse of any type, central air, water or steam heating is suitable. The exception is buildings that do not require heating. You can choose the best option for warehouse heating and make an accurate calculation of warehouse heating by contacting Airvec. We will calculate the most economical option based on the needs of the building.
You may also like...
| 
